Last but not least, a bad thermopile is one of the major reasons behind the Honeywell hot water heater status light-off issue. If your electronic ignition water heater, will not light, then it could be a loose wire, the ignition may not be getting the correct voltage, or you may just need to try lighting it more than once. Tripped Heater Thermal Switch 6. Finally, inspect and replace the broken anode rod. A lack of combustion air, there creates carbon monoxide in a greater amount which blows out the pilot. If, for whatever reason, there isnt a pilot light or it gets blown out, the thermocouple will cool and stops generating electricity, causing the gas valve to close and the unit to shut down. Then, check to see if the water line is correctly connected to the heater. Ensure each of the heating elements is blockage free. And then, pry off the igniter from the plastic assembly. It may be rust, oil, grime, dirt, or excess air in the system. You can order parts online like on Home Depot or on Amazon. The igniter itself when out of the control panel sparks fine but when connected it does not spark at all. Check and clean out the debris from the tube using a needle or this type of object. The problem indicates that there are problems with the gas supply. > Replace lousy thermostat, & faulty gas control valve turned off the thermostat/control valve. If your water heater does not have a digital readout or an automatic reset thermostat, you can test it by turning the knob to the off position and waiting 10 minutes. Heater Knob Stuck 10. First, inspect the pilot. Replace the defective one. Your gas water heater may fail to heat for the following reasons: Your water heater stops producing heat when it fails to receive enough gas. Honeywell Water Heater Keeps Turning Off, 5. But make sure youre not pulling it. Here are some instructions on how to do so. Finally, you have to reset the tripped thermal switch to get back the element function again. We store towels, medicine, toiletry supplies, first-aid gear, massage devices, facial steamers, spare Painting your garage is a great way to improve the look of the space and make the walls easier to clean. Inspect the base-ring filter and the flame arrestor to look for any dirt and debris. Whether it be identifying the problem or replacing a part, let's take a look at what you should do when your water heater igniter won't spark. We need them to do laundry, take showers, clean dishes, and much more. If you are having a problem with your igniter lighting your water heater, then chances are it is not a problem that resetting it will fix. The problem starts with this element when there has a limited voltage supply. Remove the front access panel of your water heater. Thenswitch the dial to very hot for 10 seconds. There is no particular reset button on your Honeywell water heater digital thermostat. Heater Flammable Vapor Sensor Lockout 7. This leaves you with two possible solutions. Lets start: The Honeywell heater users often complain about a major problem: the Honeywell water heater keeps turning off or wont stay lit. The gas shut-off valve is not opened all the way. To solve this problem, use a wire brush to remove any dirt or corrosion from the inside circuit at the top of the water heater tank and try lighting it again. Then, clean out the flame arrestor using a household brush. Now check for sediment build-up at the bottom of the tank as it may be the culprit for reducing the amount of heat. If the water heater is leaking, you may also see water on the floor or in the sink. > Bad outer poor thermostat knob/gas control valve set to on position. Problem with the thermocouple: If you have tried it multiple times and waited for the correct amount of time, and it is still not working, you will need to move on to the next possible issue. If it is an intermittent pilot igniter, then you will have to make sure the pilot is lit, before turning it on. To get a better look, consider dimming the lights in the room. If you are unsure about what you are doing, do not hesitate to call a service professional. Remove the two connectors of red and white wires from the gas control valve. Instead, they use electronic ignition or a spark ignitor to ignite the gas. Wait for a few moments to clear out any gases in the lines. The main reason for the Honeywell water heater not becoming hot enough is the malfunctioning of the thermostat. The main reason for the Honeywell water heater not becoming hot enough is the malfunctioning of the thermostat. When this component gets damaged by corrosion or bent, it wont function anymore. If your Honeywell water heaters thermostat is bad, your heater will produce no hot water or enough hot water. But it should not exceed 120F or 49C. We and our partners use data for Personalised ads and content, ad and content measurement, audience insights and product development. Now carefully detach each of the electrical connectors to the gas control valve. That way, you can correct them and return your water heater to proper functionality. Just follow the below few simple steps to relight the pilot with Honeywell Gas Control Valve: Step #1: Start by turning off the gas control knob to the Off position. The knob can get stuck in the On/Off/Pilot position. Inspect the water heater for any visible cracks or leaks present. The Honeywell water heater has 3 types of blinking lights. If the ignition fails, the water will not get hot enough. Then, release the knob and it should pop back up. Heater Overheating 9. Then solve this problem by following the quick solutions below: Your heater will not turn on and stop working when your Honeywell water heater error code flashes. In other words, you cant ignite your water heater. The other reasons for water heater shutting down unexpectedly include: A water heater can overheat for many reasons, but the most common cause is a failure of the thermostat. Using your manual, enter the thermostat configuration and change the system type setting and re-attempt to call for heat/ return to step 1. 01 - Water Heater Igniter. 185.23.118.97 Thank for your feedback. Usually, next to your heaters pilot light, you will find the thermocouple. Eric,your tutorial was very helpful, Im from El Paso as well. If the pilot light wont light and there is no spark, the problem usually lies with the spark electrode. So, whenever you start to struggle with any issue with your heater, just follow our Honeywell water heater troubleshooting guide and fix it by yourself. If you feel some slack, you will need to tighten it, to correct this problem. Learn more, Facebook II Twitter II Pinterest II Linkedin. One possibility is that the electrical wiring to the igniter is damaged. Some people refer to this problem as a flare out or simply pilot failure. Bathroom closets are often catch-alls for anything and everything remotely related to self-care. Turn the control knob to the ON position. Honeywell Water Heater Not Lighting. Just follow the troubleshooting steps I mentioned and fix them. However, if the pilot flame will not light after you click the igniter, you need to verify that a spark is happening inside the pilot. If yes, release the valve and set the knob to your desired temperature setting. > Replace the bad electrode. Check out any corrosion in the connections. The igniter will have multiple wires that go to it. Turn the thermostat to its lowest possible setting. Each of them indicates different problems. If your pilot flame lights but keeps going out, its vent is most likely dirty and/or clogged. The control board will throw a code if there is a problem with the voltage. Then go for the other solutions below: Due to the Honeywell water heaters flammable vapor sensor lockout, your heater stops heating water. Due to the high temperature, the T&P starts leaking. If there is no light, be sure dirt and debris have accumulated on the pilot assembly that is preventing lighting the burner. To do this, turn the water temperature dial to Low and the On/Off/Pilot knob to Pilot. Similarly, there are some other causes due to the water heater igniter not working: Honeywell water heater leaking is one of the common problems among water heater users. Also, make sure there are no flammable vapor-creating objects like paint, or gasoline nearby the heater. Your water heaters control knob will not turn off or move to the pilot position if it is stuck in the On position. Here are many more reasons for water heater leaking: There are a few possible reasons why your Honeywell water heater control might not be working. Due to inadequate gas, your heater fails to ignite and heat the water. We and our partners use data for Personalised ads and content, ad and content measurement, audience insights and product development. Sometimes due to low fuel, the heater may start beeping. Then, set the gas control knob to the Off position to turn off the unit. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data. It does not blink at all.If you could get back to me, I really would appreciate it.915-921-5951. The thermopile unit controller of the water heaterconverts thermal energy into electrical energy. Its essential to regularly clean your water filter to avoid this issue, and if you find that its already clogged, youll need to replace it. Faulty Gas Control Valves Electrical Connections. If you have reached this point, you will need a licensed professional to take a look a the valve and replace it. Position the lighter over the end of the pipe by the burner. Turning the knob will change the water temperature in the tank. Save my name, email, and website in this browser for the next time I comment. The reasons behind this difficulty are: Before your too-hot Honeywell water heater creates any major hitch, you need to fix it immediately. Then, install it and push it into its place. > Replace the faulty, broken, bent, or damaged temperature sensor. Honeywell Ignitor - How to Replace a Water Heater Ignitor FIX IT Home Improvement Channel 98.1K subscribers Subscribe 213 65K views 8 years ago Subscribe and visit our weekly FIX IT Home. Start troubleshooting simply by increasing the thermostats temperature as the temperature may turn down anyhow. Your Honeywell water heater can leak from the bottom due to the improperly maintained drain valve. Regardless, these elements can release toxic chemicals when they burn, so you should look into having a repair done immediately. Once youve resolved any potential issues with the electricity, now look at the temperature gauge of your water tank (on top) and check if it indicates a less severe problem that can be handled alone by fixing any clogs inside the tank rather than having to replace your entire unit itself which could prove to be costly. The pilot lights the gas burner for the water heater. A thermocouple is an important part of your electric kitchen or gas grill. If this doesnt work, then it might mean that the spark electrode is defective so you will have to replace it before being able to light your pilot light again. Or reset your water heater. You will see two black connectorson the gas control valve. COPYRIGHT 2023. Unfortunately, this often means that you need to replace the spark electrode. The most common symptoms of a broken water heater are the smell of gas. Still, if the knob remains in the same position, you should do the following: Note: Dont use any oil to fix the stuck knob. Continue with Recommended Cookies. When the piezo igniter is pressed down and released, an electric spark is produced to light the primary gas burner in the water heater. Anyway,the process to test your own thermopile is relatively simple. Repair the damage to stop beeping. If this is defective and does not work properly, it can cause the ignition process to stall at certain junctures within the said process, preventing the water heater from turning on. The root reasons behind Honeywell hot water heater no status light includes: Furthermore, due to tripped thermal switch, lack of combustion air, and defective heater thermopile, owners will face no status light blinking issue on their water heaters. However, the most standard procedure for lighting a gas water heater pilot light is as follows: Again, this process may vary slightly based on the make and model of your water heater. Another possibility is that there is something blocking the igniters contact with the wire coil in the furnace. Follow the below instructions: Step #1: First up, shut off the gas shut-off valve. The other responsible factors of it are: When your water heaters 1 or 2 parts stop working, you will experience your Honeywell water heater with no pilot light or weak pilot light. The board uses blinking lights, to identify which code is being thrown. The root reasons for this trouble are: After turning on your heater, wait for 90 seconds. Also, dirty pilot tubes, faulty gas valves, and clogged air vents are other possible reasons behind this. If the control board is faulty, it might also need to be replaced. Troubleshooting Common Problems Water heater not heating 10 possible causes and potential solutions Learn More Featured Video 02:24 Water heater leaking 2 possible causes and potential solutions Learn More Featured Video 01:22 Water heater not lighting 5 possible causes and potential solutions Learn More Featured Video 01:21 Water heater too hot Bathroom closets are often catch-alls for anything and everything remotely related to self-care. Now learn all the probable reasons in detail and how to break down the culprits with ease by following the suggested methods. Consequently, the pilot wont light and the status light will not blink. The sediment contains different chemicals and salt. Unfortunately, this often means that you need to replace the spark electrode. 5 Mediocre Sports Stars Who Achieved Greatness Late in Their Careers, Honeywell Water Heater Status Light Not Blinking, Zoeller Sump Pump Wont Turn On [7 Easy Solutions], Bosch Tankless Water Heater Maintenance [The Complete Guide], Igniter wires come loose from the white connector, The thermopile gets covered with carbon deposits. Water heaters are not appliances that are relatively safe to work with. Any time you work on a hot water heater, you need to make sure that it is unplugged, and that the gas is turned to the off position. Now look for any soot build-up in the pilot light tube that is preventing the pilot light from lighting. Quick Solutions For Honeywell Water Heater Status Light Not Blinking, Honeywell Hot Water Heater No Status Light [7 Easy Solutions], 4. Next, reattach everything like the wiring, manifold tube, and pilot tube to the gas control valve. Weve also outlined some other common water heater pilot light problems and how to fix them. Clean the pilot tube using a sharp object to remove the blockages. > Replace the bad gas control valve, thermostat knob, faulty outer door, weak pilot, and faulty thermostat to ensure proper gas supply to the heater. There are several factors for continuously tripping the thermal switch. First up, check all the pipe connections of the water heater. Required Part Water Heater Igniter If the igniter wires come loose from their connector, the controller will receive no signal for ignition. When you click on the igniter, there should be a tiny spark happening inside of the pilot. Hold down the pilot button and keep depressing the igniter button until the pilot light comes on. You should replace your heaters faulty internal parts such as the thermocouple, thermostat, pilot, gas control valve, igniter, thermal switch, pressure switch, etc.